on the login page. 0000241152 00000 n
0000215176 00000 n
As standard, the type of construction IM B14 is then stamped on the rating plate. 0000028387 00000 n
digit 4. endobj On LHS, 16th position of Motor Order No. 0000003647 00000 n
Two auxiliary terminals are provided in the connection box. At rated output with converter fed operation, the motors will be used in temperature class 155 (F). According to the standard, longer operation is not recommended for Category B. The warning temperature is 145 C, and tripping temperature is 155 C. 1LE0 series motors are supplied with the ball bearing as standard. 15th position of Motor Order No. 0000262563 00000 n
0000318929 00000 n
The order variants for motor protection are coded with letters in the 15th position of the Motor Order No., or ordered with Option code. For normal flat leather belts with an idler pulley, c = 2. The table below contains the permissible Radial Force values in Newtons with the assumption of zero axial forces. endobj When. Unless stated, otherwise the cable entry is located in the standard position as show in the following illustration. Rated power output: 0.55kW~315kW at 50Hz. construction and mounting type, the 16th digit of motor order No. 4 0 obj 0000085581 00000 n
All motors are designed to IP55 degree of protection (IEC 60034-5) . On RHS, 16th position of Motor Order No. These motorsare designed and manufactured in accordance with ISO, IECstandards, GB standards. The bearing lifetime of motors with horizontal type of construction is at least 40,000 hours if there is no additional axial loading at the coupling output and at least 20,000 hours with the maximum admissible loads. xref
The position of terminal box can be indicated on the 16th digit of motor order code. 0000331872 00000 n
At operating speeds above rated speed the noise and vibration levels increase and the bearing life time reduce. 0000004220 00000 n
As an already registered user simply enter your userame and password in the login page in the appropriate fields. The position of connection box is described by viewed from drive end (DE). This can, however, only be achieved if the motor is operated in accordance with the catalog specifications. 0000085683 00000 n
0000087967 00000 n
Dimension xmax. endobj - Motor winding is protected with PTC thermistors with 3 embedded temperature sensors for tripping. Standard mounting construction according to IEC 60034-7: IM B3, IM B5, IM B35 and etc. The use of a separately driven fan is recommended to increase motor utilization at low speed; When motor speed significantly higher than the synchronous speed, the separately fan is also recommended to be used. For motors which can be regreased at defined regreasing intervals, the bearing lifetime can be extended and/or unfavorable factors such as temperature, mounting conditions, speed, bearing size and mechanical load can be compensated. Connection be done through 2 auxiliary terminals in the connection box. Some converters from Siemens determine the motor temperature using the resistance of the temperature sensor. 0000148625 00000 n
0000028725 00000 n
Towards the drive end (DE)Rotation of connection box by 90, entry from DE, Option code R10. 25, Yangan Lane, Longqiao Village, Oubei Street, Yongjia County, Wenzhou, Rotating electrical machines Part 1: Rating and performance, Rotating electrical machines Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles), Rotating electrical machines Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification, Rotating electrical machines Part 6: Methods of cooling (IC Code), Rotating electrical machines Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code), Rotating electrical machines Part 8: Terminal markings and direction of rotation, Rotating electrical machines Part 9: Noise limits, Rotating electrical machines Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher Measurement, evaluation and limits of vibration severity, Rotating electrical machines Part 1: Frame numbers 56 to 400 and flange numbers 55 to 1080, Safety requirements of small and medium size rotating electrical machines, Electrical insulation Thermal classification, Classification of environmental conditions Part 2-1: Environmental conditions appearing in nature Temperature and humidity, Efficiency class according to GB standard, Efficiency class according to IEC standard, With feet and without flange on the end-shield (DE), Without feet and with flange on the end-shield (DE), With feet and with flange on the end-shield (DE), Without feet and with C-flange on the end-shield (DE), With feet and with C-flange on the end-shield (DE). Connection be done through 4 auxiliary terminals in the connection box. This will reduce the life of bearing; When the motor vibration increase due to the environment or other equipment, the bearing also will endure more radial and axial force. 6 0 obj FS 80 ~ 90 motor donot have eyebolt; FS 100 ~ 355 all motors have 2 eyebolts. Corresponds to the length of the shaft extension. the characteristics and the length of the connection leads between the converter and motor. This assumes that the motor is operated at 50Hz. 0000001613 00000 n
Insulation system is designed for temperature class 155 (F). 0000024691 00000 n
When 1LE0 with converter fed operation, KTY84-30 is recommended to be configured for winding protection. This would result in destruction of the semiconductor. The 1LE0 standard motors are fitted with an radial flow fan for cooling in accordance with IEC 60034-6 cooling method. All the connection box have 2 cable entries, one is sealed by the cable gland, and another sealed by screwed plug. %%EOF 0000313826 00000 n
It is specified as the A-valued measuring-surface sound pressure level Lpfa in dB (A). <]/Prev 375004>> 0000028500 00000 n
0000028794 00000 n
IEC 60034-1 differentiates between Category A (combination of voltage deviation 5 % and frequency deviation 2 %) and Category B (combination of voltage deviation 10 % and frequency deviation +3 % / -5 %) for voltage and frequency fluctuations. On top (Standard), 16th position of Motor Order No. Frame material: grey cast iron or aluminum alloy. Variable location of connection boxes and cable entries as option. 4-pole, 15 kW, IM B5, 380VD/660VY 50 Hz, IP55, connection box on top and cable entry at right side (view from DE), with separately driven fan. The following approximate value can be assumed. 0000008497 00000 n
IE2, Low voltage three phase cast iron motor. The temperature of the winding can be accurately monitored thanks to its lowheating capacity and the excellent heat contact with the winding. 0000215271 00000 n
The motors can supply their rated torque in both Category A and B. must be "4". Some protection method about winding protection and bearing protection are shown in the following. In Category A, the temperature rise is approximately 10 K higher than during normal operation. 0000028895 00000 n
Winding protections with PTC, PT100 and KTY84-130 as option. Towards the left side (opposite to Standard)Rotation of connection box by 180, entry from opposite end, Option code R12. 0000213920 00000 n
220VD / 380VY 50 Hz0.55 kW ~ 3 kW 2, 380VD / 660VY 50 Hz4 kW ~ 315 kW 2 , Motor protection with PTC thermistors with three embedded temperature sensors for tripping, Motor protection with PTC thermistors with six embedded temperature sensors for alarm & tripping, Motor temperature detection with embedded temperature sensor KTY84-130, Installation of three PT100 resistance thermometers, Installation of six PT100 resistance thermometers, Temperature class 155 (F), used according to 155 (F), with service factor (SF1.1, Anti-condensation heater for 220 VAC (spaces heater), Connection box on top cable entry on right (view from DE) (Standard version), Rotation of the connection box through 90, entry from DE, Rotation of the connection box through 90, entry from NDE, Rotation of the connection box through 180, Bearing design for increased cantilever forces, Installation of 2PT100 screw-in resistance thermometers for bearing, Measuring nipple for SPM shock pulse at DE measurement for bearing inspection, Mechanical design and degrees of protection, IP56 degree of protection (non-heavy-sea), Fan motor (Without fan and fan cover, NDE closed), LL861900200Mounting of LL861900220 rotary pulse encoder, Mounting of Omron rotary pulse encoder (E6B2-C) and separately driven fan, Mounting of Omron encoder (E6B2-CWZ1X) and separated driven fan, Acceptance test certificate 3.1 in accordance with EN 10204, CE markIE2 motor use with variable speed drive only, Design for TH, W, F1, WF1 and Sea air resistant, Dimension designation according to IEC standards, IM B5, IM B35, IM V1, IM V3IM B14, IM V18, IM V19. Slip 20 % (for motors < 1 kW 30 % is admissible). 1LE0 motors bearing has no protection as standard. 5 0 obj 0000000016 00000 n
Reinforced bearings for increased cantilever forces for FS100 ~ 355 as option. 0000004185 00000 n
While motor operating 60 Hz with no load, the values are approximately +4 dB (A) higher. Aluminum housing motors FS100~160 have integrated cast eyebolts.
0000011964 00000 n
0000017749 00000 n
The circumferential force FU (N) is calculated using the following equation. 0000088773 00000 n
Attention should be paid to the re-greasing intervals and the grease service life. %PDF-1.6
%
When the separately driven fan is mounted, the length of the motor increase by 6L. If necessary, FS100 ~ 250 motor can be configured with regreasable bearing and regreasing device (Option code: L23). Towards the non-drive end (NDE)Rotation of connection box by 90, entry from NDE, Option code R11. 1LE0 series motors are designed for temperature class 155 (F). 1LE0 motors are suitable for pumps, fans, compressors, texitle machine and mechanical machine applications where variable or constant speed is required. For FS80 ~ 160, the floating bearings are assembled; for FS180 ~ 355, floating bearing at DE, and fixed bearing at NDE assembled. For higher coolant temperatures and / or site altitudes higher than 1000 m above sea level, the specified motor output must be
- Installation of 3 PT100 resistance thermometers. 0000002611 00000 n
0000228283 00000 n
Installation of 2 PT100 screwed-in resistance thermometers for 1LE0 motor bearings, Option code: Q5A. Total cantilever force is calculated using the following equation. Please inquire Siemens about the detailed information of insulated bearing. The standard bearing can endure a maximum cantilever force, referred to page 11 - Permissible cantilever forces. 0000020254 00000 n
- Motor winding is protected with two sets of three temperature sensors, one set is for warning, another set for tripping. The most comprehensive protection against thermal overloading of the motor is provided by PTC thermistors (thermistor motor protection) installed in the motor winding.
Motors with this type of protection are recommended for heavy duty starting, switching duty, extreme changes in load, high ambient temperatures or fluctuating supply systems. This is evaluated by a tripping unit and can be used to open auxiliary circuits. 15th position of Motor Order No. After logging in you will see your user specific settings and prices as well as having other functions at your disposal.If you have forgotten your password please use link "Forgotten Password?" cover are also possible as long as no condensation drainage holes (Order code: H03) and no stamping of these types of construction on the rating plate are required. 0000001376 00000 n
The switching hysteresis of the PTC thermistor and tripping unit is low, which supports fast restarting of the drive. It can help reduce the motor noise. The standard insulation of the 1LE0 motors is designed such that operation is possible on the converter at mains voltage up to 460 V. 1LE0 motors are capable for converter-fed operation with certain characteristics load, of which the load torque characteristics is referred in the following diagram: By usage with admissible torque and below, the motor can be operated with self cooling; by usage over the admissible torque line, the motor with forced ventilation is needed. <>>> The connection box can also be rotated such that the cable entry is located. Connection be done through 6 auxiliary terminals in the connection box. hb``0f``= $&1f faX`$j
LQL\sx3Tqrn`=!!!A#7R&y_132c 0000015119 00000 n
digit 5. The table to the left displays only matching products according to: This kind of information is not available for this product. For special synthetic belts (depending on the type and load), c = 2 to 2.5. 
siemens motor option codes
